|Iron sights mounted on the side of a rail allow a shooter to use a scope for long-range work and iron sights when things get up close and personal.|
The Upper Hand
Plus, you can add quick-on-and-off peeps and front sights. Having numerous options for attaching the front sight to a picatinny rail-type forearms and gas blocks really adds to the gun’s versatility. But with only a few exceptions you can’t have both a scope and iron sights at the same time.
DPMS Panther Arms has added more utility to the flat-top upper, letting the rifle be a close-quarters battle weapon complete with lights or a long-range varmint/sniping gun with some accessories. Don’t get me wrong. I still love a bolt gun, but the AR can easily be changed for various utilities. And the DPMS picatinny-railed upper allows even more options to this already modular weapon. I decided to try one.
You don’t have to use the rails on the railed upper, but they are there if needed. It could offer another way to add peep sights to a scoped rifle. Most scopes have a minimum focusing distance, and a blurry sight picture is unacceptable in combat. A scoped rifle or carbine on a flat-top is difficult to operate in close-quarter situations, and an all-around tactical weapon should be ready for either.
|The improvement I like best for the AR-15 is the flat-top upper. It gives you more options for sighting and makes the rifle more scope-friendly. Plus, you can add quick-on-and-off peeps and front sights.|
This upper doesn’t have the dust cover and forward assist to which many AR users are accustomed. For those who like to tinker with ARs it’s nothing unusual to experience minor problems with the bolt closing or locking open after changes are made. Usually, if the bolt is not locking back or closing fully, replacing the buffer with a shorter or longer model will solve the problem. I’ve also occasionally experienced closing problems if the bolt isn’t fitted to the barrel. On this gun, I used a bolt and barrel that already fit properly. So just as a reminder, if you’re going to change these parts, you’ll need some slight fitting, or DPMS can sell you fitted parts.
I topped the receiver with a Leupold Mark 4 2.5-8×36 MR/T scope. It has an illuminated mil-dot reticule and is a bit shorter than other models. Shorter scopes work better on AR-15s because of the charging-handle access. A charging-handle extension is a welcome attachment for a scope, as it allows better access. The 2.5X setting gives you a better close-range sight picture, but not quite enough for close-quarters work. The AR I was using had a match stainless barrel from DPMS. One of the company’s lightweight four-rail hand guards let me add a light and front sight. With the heavy match barrel, I wanted the lightest hand guard possible. Some of the railed hand guards are quite a bit heavier than standard guards, but the DPMS guard was light enough to keep the front weight of the rifle manageable.
Streamlight makes various lighting systems for rifle work, and I gave the company’s new Super Tac light a try. It operates on 3-volt batteries and produces 135 lumens for two-and-a-half hours, and then 110 lumens for another hour. That’s plenty of light for a rifle in a combat situation. Streamlight also makes attachments to add this accessory to the hand guard accessory rail, including a vertical grip that holds the light. The grip has a hollow handle with a treaded cap for extra batteries and other necessities.
|Installation of the sighting systems is very easy. Just replace the foregrip with a railed model, align things properly and start bolting on the sights.|
DPMS’ lightweight hand guard can be adjusted on the rifle at an angle coinciding with the rail on the front or back of the upper. That lets you line it up with the flat-top upper rail for sights across the top, or angled so you can twist the rifle and use sights on the side in lieu of a top-mounted scope. You can mount DPMS’s Mangonel flip-up front and rear sights on the rails to facilitate close-quarters aiming. Then, you simply twist the rifle to the left (if you’re right-handed) and aim down the side. I suppose you could use the back rail for sighting if you’re a southpaw. The back rail would also be an excellent spot for a laser sight, especially if you didn’t have a four-rail hand guard.
I liked the two positions of the flip-up Mangonel front sight. The point of impact was a bit low when I test-fired the system, and the lower position brought it up a bit. Further adjustments can be made as usual on an AR sight by adjusting the post. These sights come with a huge lock nut that can be hand tightened in a pinch to install. When not in use, they can be folded out of the way. On a railed upper, these sights provide a longer sighting plane and the peep closer to the eye, allowing better focus.
Brownell’s carries DPMS products, of course, but also has its own rear sight in the catalog. This is a great sight that can be quickly pushed out of the way when not in service. On the back rail of the upper, it has an ample-sized hole that let in plenty of light, even in low light. It also has a large tightening knob that can be installed and removed by hand. It’s well made to withstand hard use.
|When you are all done, you have a truly universal rifle suitable for targets from point blank to 300 yards.|
For an alternate iron-sighting system, I like the Short Range Tactical sight from JP Enterprises. Brownell’s also carry this accessory. It attaches to the hand guard rail by the gas block. This sight has an open rear with an AR-type front-post setup. The front post is adjustable like AR sights, and it comes with colored inserts. When switching from the scope to iron sights by twisting the rifle, the sights are out, as if you were sighting down your favorite 1911 or other handgun. When shooting three-gun matches, this is an excellent way to engage those pesky close silhouettes that pop up between longer shots that require a scope. It’s also a nice accessory if you need to suddenly engage a close-range target.
At the Range
I took the rifle to the range, and after a half magazine was quickly placing close shots in a tight group on the hostage target. Both mechanical sighting systems worked without fail, and I could change or remove them without tools. I recommend tightening them with a tool after you have them intact to keep them from loosening up during a competition or gunfight.
— Dave Morelli is a retired policeman, having served as a patrolman, trainer, SWAT operator and a SAR tracker/trainer. He currently lives in Idaho and writes about various topics, including firearms, hunting, tactical gear and training.
Gun Digest Book of the AR-15 Vol. 2 Digital Download. Buy Now
Gun Digest Book of the AR-15 Vol II Ch. 7 Scopes Digital Download. Buy Now
About the Author: Dave Morelli is a retired Las Vegas police officer and SWAT sniper now living in Idaho. He regularly writes on topics pertaining to law enforcement, search and rescue and precision marksmanship.
Leave a Reply
You must be logged in to post a comment.